BIOS release 1.1 for NF7/NF7-S v2.0

Release information:

[ENGLISH]

0. Please use AWDFLASH 8.23D or later to update NF7 series BIOS. With 
   incorrect AWDFLASH version, the GUID will be erased, and leads to 
   IEEE1394 peer to peer function failed. AWDFLASH 8.23D is included in 
   this BIOS package. 
1. Fixes incorrectly detect Thorton 2600+(166x12.5)CPU in SoftmenuIII.
2. Fixes DRAM hang up at POST code EFh for specific memory module.
3. Fix the problem that if used CPU 400FSB without User Define,it would 
   ot show DDR xxx (xxx=200,266,333,400).
4. The default value of CPU FSB/DRAM freq revises to "Auto". 
5. Adds "CPU Disconnect Function" to adjust C1 disconnects. The Chipset 
   does not support C2 disconnect; thus, disable C2 function.
6. Fixes DMI Pool data to be Socket A, Product Name: NF7-S/NF7 (nVidia-
   nForce2), Version: 2X.
7. The frequency of CPU 1917Mhz revised to 1916MHz.
8. Update SIP table to solve systems crashed issue while using 400FSB 
   CPU+DDR 333, and revise the SIP Table of 266FSB CPU.
9. The default value of "Memory Timings" revises to "Optimal".
10.Updates BPL to be 2.94.
11.Fix system can not show fan speed in PC Health Status while using 
   lower speed FAN.
12.Add "IDE Bus Master"function to improve transfer speed of GHOST, and 
   default value set up to disabled.
13.Fix the problem that systems can not detect USB Drvice under WinME 
   resume from S3,S4 mode, and lead to usb connector failed.
14.Fine tune the OC ability of 333FSB CPU.
15.BIOS Compile Date: 3/27/2003.


[中文]

0. 請使用 AWDFLASH 8.23D 或更新版本來更新 NF7 系列主機板之 BIOS。 使用
   不適當版本的 AWDFLASH 程式，會消除 GUID 並導致 IEEE1394 peer to peer
   功能失效。 AWDFLASH 8.23D 已包含在本 BIOS 自解檔案中。
1. 修正Thorton 2600+(166x12.5) CPU在softmenu III 偵測錯誤。
2. 修正某些DRAM hang EFh的問題。
3. 使用 CPU 400FSB 在不使用 User Define 時, 沒有顯示 DDR xxx (xxx=200,266,
   333,400)。
4. CPU FSB/DRAM freq.預設值改為"Auto"。
5. 加入"CPU Disconnect Function" 功能以支援 C1 disconnect。由於晶片組不支援 
   C2 disconnect，將 C2 功能關閉。
6. 修正 DMI Pool 顯示為 Socket A、Product Name: NF7-S/NF7 (nVidia-nForce2)、
   Version: 2.X。
7. 修正 1917Mhz CPU 顯示為 1916Mhz。
8. 更新 SIP table ，以修正當使用400FSB CPU, DDR333 DRAM 當機的問題。並修改 
   266FSB CPU 使用之 SIP Table。
9. 更改"Memory Timings"預設值為 "Optimal"。
10.更新BPL 為2.94。
11.修改低轉速的風扇(1800左右轉速)在PC Health Status 內無法顯示轉速的問題。
12.加入"DE Bus Master"功能﹐預設值為disabled。
13.修改USB Device 在WinME S3,S4 resume 後﹐出現不明裝置的情形﹐導致USB 
   裝置無法使用。
14.更改CPU 400FSB SIP Table決定於GPI判斷為400FSB時使用400FSB SIP table, 
   不因為調為 200MHz 以上即使用 400FSB SIP table，以增加 333FSB CPU 超頻性。
15.BIOS 日期: 3/27/2003。

*********************************  NOTE  *********************************

1. How to upgrade BIOS:

 a. Boot into MS-DOS or "Safe mode and command prompt" if you are using 
    Windows95/98
 b. Run "nf7d11.exe" to extract all files.
 c. Run "runme.bat"

   ***  Please notice that we suggest you flashing the bios with switches 

           "/py /sn /cd /cp /cc /cks /R" or by "runme.bat".  

 d. For more detail, please visit:

    http://fae.abit.com.tw/cht/download/bioshelp.htm  (Chinese)
    http://fae.abit.com.tw/eng/download/bioshelp.htm  (English)

2.After BIOS updated, pull off the power cord and then clear the CMOS data 
  via jumper before restarting system please.


============================================================================