BIOS release 1.1 for IS7-M  V1.0


Release information:

[ENGLISH]

1. Update CPU micro code.
2. Add Pentium 4 Extreme Edition support.
3. Fixed the problem that CAS latency can not be set manually when the
   CPU:DRAM is set to PSB8000/5:4 or PSB800/3:2.
4. Fixed the problem that the system fails the diagnose test of Intel
   865G Graphics Controller Diagnostic Utility.
5. Fixed the problem that the system will hang at starting PXE if the
   OnChip SATA is set to enhanced mode and the LAN boot is enabled.
6. Add the message of how to enter BIOS setup in the full screen logo.
7. Changed the option wordings of "Boot Device" from "ZIP100" to
   "ZIP100/250" and from "USB-ZIP" to "USB-ZIP/LS120".
8. Revised the wording of memory status from "DDR at Bank" to "DDR at
   DIMM" in system configuration table.
9. Fixed the problem that system will reboot when the "Resume by Alarm"
   is enabled and user pressed power button to shutdown the system
   during POST.
10. Fixed HDD size detected as 136GB when 200/250/300 GB SATA drives
    are connected to SATA1 or SATA2 (ICH5 SATA channels).
11. Update VGA BIOS to version V3062.
12. BIOS compile date: 11/04/2003


[中文]

1. 更新CPU micro code。
2. 新增支援Pentium 4 Extreme Edition。
3. 修正當 CPU:DRAM 為 PSB800/5:4 或 PSB800/3:2 時，以手動調整 CAS Latency
   值，會有無法設定的問題。
4. 修正 Intel 865G Chipset Graphics Controller Diagnostic Utility. 測試
   fail 之問題。
5. 修正使用 Onchip SATA 並設為 enhance mode 時, 由 Lan Boot 會停在 PXE 啟動
   處之問題。
6. 新增訊息當啟動 Full Screen Logo 時，告知使用者如何進入 BIOS Setup 畫面.
7. 變更 "Boot Device" 中的選單字串為 "ZIP100/250" 及 "USB-ZIP/LS120"。
8. 修改 System Configurations 中關於記憶體的字串為 "DDR at DIMM"。
9. 修正當 Enable "Resume by alarm"選項並在 post 過程中按 power button 關機
   後, 系統會重新啟動之問題。
10. 修正無法正確顯示136G 以上SATA HD容量當 200/250/350GB SATA 裝置接到 SATA1
    或 SATA2(ICH5 SATA 接頭)時之問題。
11. 修正使用Prescott CPU在DMICFG Tool, CPU資料顯示錯誤之問題。
12. 更新VGA BIOS版本為 v3062。
13. BIOS日期: 11/04/2003


*********************************  NOTE  *********************************

1. How to upgrade BIOS:

 a. Boot into MS-DOS or "Safe mode and command prompt" if you are using
    Windows95/98
 b. Run "is7m11.exe" to extract all files.
 c. Run "runme.bat"

   ***  Please notice that we suggest you flashing the bios with switches

           "/py /sn /cd /cp /cc /cks /R" or by "runme.bat".

 d. For more detail, please visit:

    http://fae.abit.com.tw/cht/download/bioshelp.htm  (Chinese)
    http://fae.abit.com.tw/eng/download/bioshelp.htm  (English)

2.After BIOS updated, pull off the power cord and then clear the CMOS data
  via jumper before restarting system please.


============================================================================