BIOS release 1.5 for IS7    v1.0/v1.1
                                      IS7-E  v1.0/v1.1
                                      IS7-G  V1.0


Release information:

[ENGLISH]

1. Updated CPU micro code (0F29H/14H).
2. Added hot key wording to enter BIOS setup when full screen logo
   enabled.
3. Changed the option wording from "OnChip SATA" to "OnChip SATA RAID"
   for "Bootable Add-in Device".
4. Changed the default setting of "OnBoard IR Port" to "Disabled".
5. Fixed the booting failure problem of Maxtor SATA HDD (Model name:
   6Y120M0) in ICH5R RAID 0 status. (for IS7-G and IS7 only)
6. Changed the option wordings of "Boot Device" from "ZIP100" to
   "ZIP100/250" and from "USB-ZIP" to "USB-ZIP/LS120".
7. Enhanced the system stability when over clocks the CPU FSB over 255 MHz
   with CPU:DRAM = 1:1 setting. (Over clocking is out of warranty)
8. Revised the wording of memory status from "DDR at Bank" to "DDR at
   DIMM" in system configuration table.
9. Fixed the problem that specific CD-ROM device could not be correctly
   detected when there is specific HDD connected onto the same IDE cable.
10. BIOS Compile Date: 8/15/2003.

[中文]

1. 更新 CPU micro code 0F29H/14H)。
2. 當採用全螢幕 LOGO 時在其下方顯示文字提示- Del to enter BIOS setup。
3. 變更 "Bootable Add-in Device" 選項文字，從 "OnChip SATA" 改為 "OnChip
   SATA RAID"。
4. 將 "OnBoard IR Port" 的預設值修改成 "Disabled"。
5. 修正 Maxtor SATA 硬碟 (型號 6Y120M0) 在 IS7G_15 版本 BIOS 無法在 ICH5R
   南橋組成 RAID 0 的問題。 (僅 IS7-G 和 IS7 受影響)
6. 變更 "Boot Device" 選項文字，將 "ZIP100" 改為 "ZIP100/250"；同時也將
   "USB-ZIP" 改為 "USB-ZIP/LS120"。
7. 改善當 CPU:DRAM = 1:1 而且 CPU 頻率超頻至 255 MHz 以上系統不穩的問題
   (請注意超頻使用並非產品保固範圍內)
8. 更改開機時 System Configurations Table 當中記憶體狀態顯示方式，從 "DDR
   at Bank" 變更為 "DDR at DIMM"。
9. 修正某些特定光碟機和某些特定硬碟機串接在同一條 IDE 排線上會有偵測不到
   的問題。
10. BIOS 日期: 8/15/2003。

*********************************  NOTE  *********************************

1. How to upgrade BIOS:

 a. Boot into MS-DOS or "Safe mode and command prompt" if you are using
    Windows95/98
 b. Run "is7g16.exe" to extract all files.
 c. Run "runme.bat"

   ***  Please notice that we suggest you flashing the bios with switches

           "/py /sn /cd /cp /cc /cks /R" or by "runme.bat".

 d. For more detail, please visit:

    http://fae.abit.com.tw/cht/download/bioshelp.htm  (Chinese)
    http://fae.abit.com.tw/eng/download/bioshelp.htm  (English)

2.After BIOS updated, pull off the power cord and then clear the CMOS data
  via jumper before restarting system please.


============================================================================