SCSI Bus Termination / Terms

^{IBM-AUSTRIA - PC-HW-Support 30 Aug 1999}

SCSI Bus Termination / Terms - Definitions

General SCSI-cabling rules - you NEVER should ...

For have a longer SCSI cable - NEVER connect a second cable, for have a longer SCSI cable.
Not INTERNAL -or- EXTERNAL - you have to use a longer cable (do not try to solder cables).

Never make a T -or- Y SCSI adapter-connection.
Such an SCSI-bus never can be correct terminated !

SCSI Bus Termination

Failure to properly terminate the SCSI bus will result in poor (wrong) signal quality and noise on the bus. Errors caused by this condition may be intermittent, and difficult to diagnose. Improper SCSI bus termination also causes operating system load problems and IML failures.

Do NOT MIX - Single-ended and Differential devices on a single SCSI bus!
(Otherwise, if mixing be sure - have the FIREBRIGADE nearby).

Most common SCSI Standards - Specifications

Mode Bandwith Frequ. Max Data Transfer Rate Max Cable Length Single- -Ended SCSI-I 8-bit 5 MHz 5 MBps 6 meters SCSI-II 8-bit 5 MHz 5 MBps 6 meters Fast SCSI 8-bit 10 MHz 10 MBps 3 meters Wide SCSI 16-bit 5 MHz 10 MBps 6 meters Fast/Wide SCSI 16-bit 10 MHz 20 MBps 3 meters 32-bit SCSI 32-bit 5 MHz 20 MBps 6 meters 32-bit Fast SCSI 32-bit 10 MHz 40 MBps 3 meters Fast-20 SCSI 8-bit 20 MHz 20 MBps 1.5 m Fast-20 Wide SCSI (UltraSCSI) 16-bit 20 MHz 40 MBps 1.5 m

Mode	Bandwith	Frequ.	Max Data Transfer Rate	Max Cable Length Single- -Ended
SCSI-I	8-bit	5 MHz	5 MBps	6 meters
SCSI-II	8-bit	5 MHz	5 MBps	6 meters
Fast SCSI	8-bit	10 MHz	10 MBps	3 meters
Wide SCSI	16-bit	5 MHz	10 MBps	6 meters
Fast/Wide SCSI	16-bit	10 MHz	20 MBps	3 meters
32-bit SCSI	32-bit	5 MHz	20 MBps	6 meters
32-bit Fast SCSI	32-bit	10 MHz	40 MBps	3 meters
Fast-20 SCSI	8-bit	20 MHz	20 MBps	1.5 m
Fast-20 Wide SCSI (UltraSCSI)	16-bit	20 MHz	40 MBps	1.5 m

NOTE: Fast-20 Wide SCSI is also reffered to as UltraSCSI single ended. The single ended refers to the length of the SCSI cable w/o using differential technology and w/o the use of a SCSI repeater.

With an SCAM (SCSI Configured AutoMagically) Adapter installed, the adapter use ID #6 during BOOT. All to an SCAM-adapter connected devices should support SCAM - otherwise conflicts.

The SCSI bus is a high speed bus that operates at speeds up to 5 megabits per second. The bus must be terminated properly at both ends with resistor networks to minimize signal reflections on the bus and to ensure proper voltage levels.

The following -PASSIVE- SCSI termination schemes may be encountered in the field:
(Only valid for passive SCSI-2 HD's - NOT valid for ULTRA, RAID and differential SCSI devices! )

SCSI Adapter/A without cache - a T-RES terminator is on the adapter and is described in Rule 4.
SCSI Adapter/A with cache - this adapter has no T-RES terminator onboard and is described in Rule 5.
Integrated SCSI controller - A T-RES terminator is on the system board and is described in Rule 6.

The following rules are a guide for proper -PASSIVE- SCSI termination:

The SCSI bus must always have a terminator on the device at the physical end of the SCSI bus. These devices include hard disks, tape drives, CD-ROM drives, and the SCSI adapter itself, if no devices are connected to one of the interface.
Terminators are installed only at the ends of the SCSI bus. Terminators installed on devices that are not at the end of the bus must be removed from the devices. Failure to do so results in excessive current on the SCSI bus. This can cause early life failure of any attached SCSI device, if operated for extended periods of time. The point of failure is the bus drivers on the SCSI devices, which break down due to excessive power dissipation.
When installing SCSI devices on the internal interface, always attach a device to the last physical connector on the cable.
For the IBM PS/2 SCSI Adapter/A with the onboard T-RES terminator, termination of the adapter is accomplished when the 20 Pin T-RES terminator is in its socket. (The terminator is usually orange in color.) The T-RES terminator must be removed from the adapter if both internal and external devices are attached to the adapter. In this situation, the SCSI bus is terminated at the last device on the internal cable and the last device on the external cable.
For the IBM PS/2 SCSI Adapter/A with cache (no onboard terminator), termination of the adapter is done in one of the following ways:
1. If only external devices are connected to the adapter, attach the internal terminator to the edge card on top of the adapter and terminate the last device on the external SCSI cable.
2. If only internal devices are connected to the adapter, attach the external terminator to the connector at the rear of the adapter and terminate the last device on the internal SCSI cable.
3. If both, internal and external devices are connected, termination is done on the last device on the internal cable and the last device on the external cable.
For the SCSI controller built into the system board, there is a T-RES terminator on the system board. The termination of the SCSI bus is accomplished when the 20 Pin T-RES terminator (usually orange in color) is in its socket. The T-RES terminator must be removed when both, internal and external devices are attached to the controller. In this situation, the SCSI bus is terminated at the last device on the internal cable and the last device on the external cable.

A useful publication for systems using SCSI devices is:
International Technical Support Centers, SCSI Arrchitecture and Implementation, GG24-3507-00

The following technical letter was found on INTERNET (Adaptec)

SCSI Terms and Definitions

There are 2 handshaking modes on the SCSI bus, used for transferring data: ASYNCHRONOUS and SYNCHRONOUS. Asynchronous is a classic Req/Ack handshake. SYNCHRONOUS is 'sort of' Req/Ack, only it allows you to issue multiple Req's before receiving Ack's. What this means in practice is that SYNCHRONOUS transfers are approx 3 times faster than ASYNCHRONOUS.

SCSI-1 allowed asynchronous transfers at up to 1.5 Mbytes/Sec and synchronous transfers at up to 5.0 Mbytes/Sec.

SCSI-2 had some of the timing margins 'shaved' in order that faster handshaking could occur. The result is that asynchronous transfers can run at up to 3.0 bytes/Sec and synchronous transfers at up to 10.0 Mbytes/Sec. The term 'FAST' is generally applied to a SCSI device which can do syncrhonous transfers at speeds in excess of 5.0 Mbytes/Sec. This term can only be applied to SCS1-2 devices since SCSI-1 didn't have the timing margins that allow for FAST transfers.

Differential SCSI

For each signal that needs to be sent across the bus, there exists a pair of wires to carry it. The first in this pair carries the same type of signal the single-ended SCSI carries. The second in this pair, however, carries its logical inversion. The receiver takes the difference of the pair (thus the name differential), which makes it less susceptible to noise and allows for greater cable length.

Single-ended SCSI (normal SCSI)

For each signal that need to be sent across the bus, there exist a wire to carry it.

Wide SCSI

SCSI may now transfer data at bus widths of 16 and 32 bits. Commands, status, messages and arbitration are still 8 bits, and the B-Cable has 68 pins for data bits. Cabling was a confusing issue in the closing days of SCSI-2, because the first project of SCS1-3 was the definition of a 16 bit wide P-Cable which supported 16-bit arbitration as well as 16-bit data transfers. Although SCSI-2 does not contain a definition of the P-Cable, it is quite possible that within the year, the P-Cable will be most popular non-SCSI-2 feature on SCSI-2 products.

Fast SCSI

A 10 MHz transfer rate for SCSI came out of a joint effort with the IPI (Intelligent Peripheral Interface commitee in ASC X3T9.3. Fast SCSI achieves 10 Megabytes/second on the A-Cable and with wider data paths of 16 and 32 bits can rise to 20 Megabytes/second and even 40 Megabytes/second. However, by the time the market starts demanding 40 Megabytes/second it is likely that the effort to serialize the physical interface for SCSI-3 will attract high-performance SCSI users to the Fiber Channel.

A word of caution. At this time the fast parameters cannot be met by the Single Ended electrical class, and is only suitable for Differential. One of the goals in SCSI-3 is to identify the improvements needed to achieve 10 MHz operation with Single Ended components.

SCSI Termination (PASSIVE-termination)

The Single Ended electrical class depends on very tight termination tolerances, but the passive 132 ohm termination defined in 1986 is mismatched with the cable impedance (typically below 100 ohms) Allthough not a problem at low speeds when only a few devices are connected, reflections can cause errors when transfer rates increase and/or more devices are added. In SCS1-2, an active terminator has been defined which lowers termination to 110 ohms and is a major boost to system integrity.

Command Queueing

In SCSI-1, initiators were limited to one command per LUN e.g. a disk drive. Now up to 256 commands can be outstanding to one LUN. The target is allowed to re-sequence the order of command execution to optimize seek motions. Queued commands require Tag messages which follow the Identify.

Is SYNCHRONOUS faster than ASYNCHRONOUS ?

Asynchronous is faster on short cables, while synchronous is faster on long cables. The reason has to do with the propagation delay of the cable; the turn around time of the silicon; and the interlocked nature of the asynchronous handshake.

We have measured propagationdelays from various cables and found an average of 1.7 nanoseconds per foot, which is roughly 5.25 ns per meter.
The turn-around time is the amount of time the SCSI chip takes to change an output in response to an input. If REO is an input then ACK is an output. Or if ACK is an input then REQ is an output. Typical turn-around time for the 53C90 is 40 nanoseconds.
The asynchronous transfer uses an interlocked handshake where a device cannot do the next thing until it receives positive acknowledgment that the other device received the last thing.

First REQ goes true (driven by Target) , then ACK is permitted to go true (driven by Initiator) , then REQ is permitted to go false, then ACK is permitted to go false.

Thus we have four 'edges' propagating down the cable plus 4 turn-around delays. Asynchronous transfer requires 55 ns setup and no hold time (paragraph in 5.1.5.1 in SCS1-1 or SCS1-2) which gives an upper speed limit around 18 MB/s. A detailed analysis shows that the setup time subtracts out. This is mostly because we are running at one-third the max rate, but also because setup for the next byte can begin anytime after ACK is received true or REQ is received false, depending on who is receiving. You can either take my word for it or draw the waveforms yourself. Thus, the asynchronous transfer reduces to:

4 * 1.7 * 1) + (4 * 40 ns) = 167 ns = 6 MB/s (1 foot cable)

(4 * 5.25 * 6) + (4 * 40 ns) = 286 ns = 3.5 MB/s (6 meter cable)

(4 * 5.25 * 25) + (4 * 40 ns) = 685 ns = 1.5 MB/s (25 meter cable)

Note: Cables longer than 6 meters require external differential transceivers which add delay and degrade the performance even more than indicated here.

Our simulations say that under very best conditions (fast silicon, low temperature, high voltage, zero length cable) we can expect more than 8 MB/s asynchronously. In the lab, I routinely measure 5 MB/s on 8 foot cables. So, if you were writing the data manual for this, how would YOU spec it?

The framers of the SCSI spec threw in synchronous mode to boost the performance on long cables. In synchronous mode, the sending device is permitted to send the next byte without receiving acknowledgment that the receiver actually received the last byte. Kind of a ship and pray method. The acknowledgment is required to come back sometime, but we just don't have to wait for it (handwave the offset stuff and the ending boundary conditions). In this mode any external transceivers add a time shift, but not a delay. So if you negotiate for 5 MB/s, you get 5 MB/s regardless how long the cable is and regardless whether you are single-ended or differential. But you can't go faster than 5.5 MB/s, except in SCSI-2.

Synchronous mode does have a hold time (unlike asynch) but again, setup and hold times subtract out. In SCSI-1 synchronous mode, the speed limit comes from the combined ASSERTION PERIOD + NEGATION PERIOD which is 90ns + 90ns = 180 ns = 5.5 MB/s. Our 53C90 family doesn't quite hit the max, but we do guarentee 5.0 MB/s. In SCSI-2, anything above 5.0 MB/s is considered to be FAST. Here the maximum transfer rate is explicitly limited to 100 ns or 10MB/s; you don't have to read between the lines to deduce it.

Interesting tid-bit: given a SCSI-2 FAST period of 100 ns and a cable delay of 131 ns on a 25 meter cable, you can actually stack 1.31 bytes in the 8-bit cable. In FAST and WIDE SCSI you can stack 5.24 bytes in this copper FIFO.

Active / Passive - Terminator sample

An active terminator actually has one or more voltage regulators to produce the termination voltage, rather than using resistor voltage dividers.

This is a PASSIVE terminator: (one signal-line example)

Notice that the termination voltage varies with the voltage on the TERMPWR line. One voltage divider (two resistors) is used for each SCSI signal.

An ACTIVE terminator looks more like this:

You MUST use ACTIVE-termination if an ULTRA or RAID SCSI adapter is installed !
(It's not wrong to use active termination if bus-speed is <= 10MByte/sec, but if bus-speed > 10MByte/sec, you must use active termination).

Assuming that the TERMPWR voltage doesn't drop below the desired termination voltage (plus the regulator's minimum drop), the SCSI signals will always be terminated to the correct voltage level.

Server 325/330 recommendations for ULTRA-SCSI (SCSI-3) support are:

NOTE: The following are guidlines, and many setup which break this rules will still work. Setups which stick to the below rules will have the best chance of working.

Maximum of up to 7 devices (plus the controller) if the cable length is 1.5m (4.5-ft) or less.
Maximum of up to 3 devices (plus the controller) if the cable length is 3.0m (9-ft) long.
8-bit and 16-bit devices can be mixed (ensure 16-bit at end of chain).
SCSI-3 and legacy devices can be mixed. Beware of capacity loading of older devices though.
To support more devices (up to 15) or to support external SCSI devices, ULTRA-SCSI support should be disabled in the SCSI Select utility.
This restrictions basically say that ULTRA-SCSI is an internal solution only.

Mixing SCSI Types.

The prime concern when intermixing devices operating with differen SCSI configurations is the data bus width. The 50-pin connector used for external SCSI-1 and SCSI-2 FAST devices will not support greater than 8 bits.
So to use WIDE devices, they must be placed physically before the 8-bit devices. Also highlighted is that the bus lines that are cut off, must be terminated as usual.

Mixing Wide and Narrow External SCSI Devices 68-pin SCSI-2 Wide or 50-pin SCSI-2 Fast or Fast & Wide device SCSI-1 device +----+ +----+ ----| |------------------------| |------ | | Control Bus | | ----| |------------------------| |------ from previous | | | | to next SCSI-1 --------> | | | | -------> or Wide device | | | | SCSI-2 FAST (only) or ----| |------------------------| |------ device Controller | | Data (0-7) | | ----| |------------------------| |------ ----| |-----------------++ | | | | Data (8-15/32) ||T | | ----| |-----------------++ | | +----+ +----+ Wide SCSI Cable Wide (68-pin) to SCSI-1 (50-pin) (68-pin) SCSI-1 (50-pin) Cable with termination (T)

For internal use the bus cable will be the same for its whole length, therefore, all signal lines can be terminated at the end. In such cases the data bus width reduction can be performed without termination.

Term-Power Rules

When SCSI-I Adapter/Devices are used, the Adapter only should supply termination power.
When SCSI-II Adapter/Devices are used each Adapter and/or Device can supply termination power. As a general rule, (for SCSI-II, F/W, Ultra..) only the Adapter should supply termination power. If the SCSI cable is very long (>1.2m), Term-Power also should/can be supplied from the last device (in chain) on this cable, but all other devices in such a chain, should not have Term-Power enabled.

The following statements, where found on Internet Adaptec http://www.adaptec.com/support

Conneting 8-bit and 16-bit Devices to an Adaptec Wide Host Adapter

Adaptec wide host adapters available: 2740W, 2742W, 2744W, 2940W, 2940UW Mac, 2944W, 2940UW, 3940W, 3940UW, 3940UW Mac, 3940 UWD and 3944UWD.

Definition - Narrow / Wide SCSI-Devices

NARROW (8-Bit) devices are connected to a 50-pin cable/connector.
The narrow signal cable carries the Low Data Bytes and the Control signals
WIDE (16-Bit) devices are connected to a 68-pin cable/connector.
The wide signal cable carries the Low Data Bytes the High Data Bytes and the Control signals

Low data byte = data bit's 0 to 7 - High data byte = bit's 8 to 15.

68-pin to 50-pin external converters are available from various manufacturers. Only converters that actively terminate the High Data Bytes should be used.

Internal Converter Kit usage

In the below example, an internal converter converts a 68-pin wide ribbon cable to a 50-pin connector. The converter is used only to convert the 68-pin to a 50-pin connetor (needed for narrow device) but has no termination for the high data byte, because a termination is only once at the end of the cable allowed/needed.

External Devices - Connection Examples.

Internal Devices - Connection Examples.

There exist several Converters / Convert-Terminators for Wide SCSI to Narrow conversion.

Active internal SE (single ended) Terminator - 68-pin wide, IBM FRU P/N 92F0322 connected to end of cable.
External Converter - Wide to Narrow (Adaptec ACK-68P-50P-E) with integrated HIGH-Bit termination.
Internal Converter - Wide to Narrow (Adaptec ACK-68P-50P-IU)
68-pin Wide SCSI - Internal Terminator (Adaptec ACK-W2W-5IT)

Back to

More INFORMATION / HELP is available at the IBM-HelpCenter

Please see the LEGAL - Trademark notice.
Feel free - send a for any BUG on this page found - Thank you.