MP078 USER'S MANUAL Intel ATX Pentium II PCI/ISA MOTHERBOARD Foreword ======== This manual is designed to provide the basic necessarv information for the end user to understand and properly use the MP078 mainboard. The mainboard ensures superlative performance and complete compatibility with industry standards, which incorporating many technical enhancements. Trademarks ========== WTC is a registered trademark of Win Technologies Co., Ltd. All trademarks belong to their registered owner. Checklist ========= Your MP078 Cache package contains the following: * MP078 Cache mainboard * User's Manual. * HDD Cable * FDD Cable * Serial & Printer Cable * CPU Heatsink * Heatsink Frame * Screws for Heatsink Frame Precautions =========== Make sure you ground yourself before handling the mainboard or other system components. Electrostatic discharge will damage mainboard. Note that you must take special precaution when handling the mainboard in dry or air- conditioned environments. The precaution below is to protect the mainboard from electrostatic discharge. * Do not remove the anti-static packaging until you are ready to install the mainboard and other system components. * Ground vourselfbefore removing any system component from its protective anti-static packaging. To ground yourself , grasp the expansion slot covers or other unpainted portion computer chassis. * Frequently ground yourself while working , or use a grounding strap. * Handle the mainboard by the edges and avoid touching its components. Mainboard Features ================== * Intel 440FX PCI chipset: 82441(PMC) / 82442(DBX) / 82371 (PIIX3) * Supports Intel Pentuim II-233MHz/266MHz/300MHz Processor(with MMX) * Five high performance 32 bits PCI local bus master * Three 16 bits ISA system bus I/O slots * Supports BEDO,EDO,FPM DRAMs,8MB up to 768MB * Supports two USB (Universal Serial Bus) ports * Enchanced IDE onboard * Support PnP (Plug and Play) function * Enhanced fast I/O ( Serial port, Parallel port (ECP/EPP/SPP), FDC) onboard * IR prot optional * Modem Ring wake up * ATX motherboard specification Jumpers and Connectors Reference ================================ Before installing the mainboard, make sure that thejumper settings are properly set for your configuration. The functions of the different jumpers are respectively as follows: CPU Clock Selector SW1 Flash ROM Voltage Selector JP13 CMOS Charge/ Discharge JP14 COM2 / IR Selector JP1, JP2 Mainboard Connectors ==================== Hard disk Connector IDE1 & IDE2 Printer Connector PRN1 Floppy Connector FDC Serial Connector COM1 & COM2 Universal Serial Bus Connector USB Power on push button Connector JP16 Power LED Connector J4 or J11(1-3) SMI Connector J8 SMI LED Connector J2 Hard disk LED Connector J9 Keylock Connector J11 Speaker Connector J10 Reset Connector J5 Turbo LED Connector J7 Turbo Switch Connector J6 Keyboard Connector KB1 PS/2 Mouse MS1 Power Supply Connector P1 or P2 IR Connector IR1 Jumper Caps reference ===================== Red cap for voltage selector Black cap for others CPU JUMPER SETTING ==================== CPU TYPE CPU Clock Selector SW1- 1 2 3 4 INTEL PENTIUM IT - 233Mhz OFF OFF ON ON INTEL PENTIUM II - 266MHz ON ON ON OFF INTEL PENTTUM II - 300MHz ON OFF ON OFF FLASH ROM VOLTAGE SELECTOR ========================== JP13 RED jumper Cap 1-2 12 VOLTS FLASH ROM (Inter / MX brand) 2-3 5 VOLTS FLASH ROM (SST / Winbond / Atmel brand) CMOS RESET CONNECTOR ==================== JP14 OPEN CMOS CHARGE CLOSE CMOS DISCHARGE OR RESET COM2 / IR SELECTOR ================== JP1 JP2 2-3 2-3 FOR COM2 PORT (DEFAULT) 1-2 1-2 FOR IR PORT MEMORY CONFIGURATION ==================== Memory supports from 4MB upto 768MB by using Standard, EDO and BEDO. MEMORY MODULE COMBINATIONS: BANK O BANK 1 BANK 2 TOTAL MEMORY SM1&2 SM3&4 SM5&6 4MB x 2 NONE NONE 8MB NONE 4MB x 2 NONE 8MB NONE NONE 4MB x 2 8MB 8MB x 2 NONE NONE 16MB NONE 8MB x 2 NONE 16MB NONE NONE 8MB x 2 16MB 4MB x 2 4MB x 2 4MB x 2 24MB 4MB x 2 8MB x 2 NONE 24MB 8MB x 2 4MB x 2 NONE 24MB 8MB x 2 8MB x 2 NONE 32MB NONE 8MB x 2 8MB x 2 32MB 16MB x 2 NONE NONE 32MB NONE 16MB x 2 NONE 32MB NONE NONE 16MB x 2 32MB 4MB x 2 16MB x 2 NONE 40MB 16MB x 2 4MB x 2 NONE 40MB 8MB x 2 16MB x 2 NONE 48MB 16MB x 2 8MB x 2 NONE 48MB 8MB x 2 8MB x 2 8MB x 2 48MB 32MB x 2 NONE NONE 64MB NONE 32MB x 2 NONE 64MB NONE NONE 32MB x 2 64MB 4MB x 2 32MB x 2 NONE 72MB 32MB x 2 4MB x 2 NONE 72MB 8MB x 2 32MB x 2 NONE 80MB 32MB x 2 8MB x 2 NONE 80MB 16MB x 2 32MB x 2 NONE 96MB 32MB x 2 16MB x 2 NONE 96MB 16MB x 2 16MB x 2 16MB x 2 96MB 32MB x 2 32MB x 2 NONE 128MB NONE 32MB x 2 32MB x 2 128MB 32MB x 2 32MB x 2 32MB x 2 192MB 32MB x 2 64MB x 2 NONE 192MB 64MB x 2 32MB x 2 NONE 192MB 64MB x 2 64MB x 2 NONE 256MB NONE 64MB x 2 64MB x 2 256MB 64MB x 2 64MB x 2 64MB x 2 384MB 64MB x 2 128MB x 2 NONE 384MB 128MB x 2 64MB x 2 NONE 384MB 128MB x 2 128MB x 2 NONE 512MB 128MB x 2 128MB x 2 64MB x 2 640MB 128MB x 2 128MB x 2 128MB x 2 768MB IMPROTANT: Do not use 72-pin SIMM module with more than 24 chips. Module with more than 24 chips exceed the design specification of the memory subsystem and will cause unreliable operation. MAINBOARD CONNECTORS ==================== IDE 1 & 2 HARD DISK CONNECTOR FDC FLOPPY CONNECTOR PRN1 PRINTER PORT CONNECTOR COM 1 & 2 SERIAL PORT CONNECTOR USB UNIVERSAL SERIAL BUS CONNECTOR MS1 PS/2 MOUSE CONNECTOR KB1 PS/2 KEYBOARD CONNECTOR IR1 INFRARED MODULE CONNECTOR J2 SMILED CONNECTOR JP16 POWER ON PUSH BUTTON CONNECTOR J4 or J11(1-3) POWER LED CONNECTOR J5 RESET CONNECTOR J6 TURBO SWITCH CONNECTOR J7 TITRBO LED CONNECTOR J8 SMI SWITCH CONNECTOR J9 HARD DISK LED CONNECTOR J10 SPEAKER CONNECTOR J11 KEYLOCK CONNECTOR AWARD BIOS SETUP ================ Award BIOS support plug and play function and has a built-in setup program that allows the users to modify the basic system configuration. This type of information is stored in CMOS so that it retains the setup information when the power is turned off. 1. Turn on or reboot the system. when the below message appears at the bottom of the screen during the POST ( Power On Self Test ) press DEL key to enter setup. 2. Press the DEL key to enter the Award BIOS program and the main menu will appear on the screen. The main menu allows you to select from ten setup functions and two exit choices. 3. For the safe, please select "LOAD SETUP DEFAULTS" for BIOS setup.